DAQ PCI Express & DAQ PCI cards accesories

TEDIA offers a wide range of accessories for its DAQ PCI Express cards.
For a more detailed view about accessories compatibility, see the compatibility tables for DAQ PCIe cards and DAQ PCI cards.

Differential amplifiers (with multiplexers)

This type of daughter boards is intended for:

modifying the S.E. inputs at the DAQ cards into differential inputs
expansion of the number of analog inputs at the DAQ cards
economic expansion of the ranges of processed signals up to the limit of the isolation amplifiers

OPT-830A	eight differential amplifiers for signals with common mode voltage up to ±250V_DC (measured difference signal up to ±10V_DC) (with DAQ PCIe cards an external power supply must be used)
OPT-830B	features like OPT-830A, but extra tri-state output drivers for expanding of the number of inputs up to 32 DIF. (up to 4 pieces OPT-830B) (compatible only with DAQ PCI cards, not DAQ PCIe cards)
DIN-830	DIN35 housing for both OPT-830A and OPT-830B

Analog multiplexers

This type of daughter boards is intended for expansion of the number of analog inputs of the DAQ cards (they switch more measured signals to the one input channel of the DAQ card).

OPT-832D	analog multiplexer 32 inputs => 8 outputs, pin-headers connectors (compatible only with DAQ PCI cards, not DAQ PCIe cards)
OPT-832W	analog multiplexer 32 inputs => 8 outputs, tool-free terminal block (compatible only with DAQ PCI cards, not DAQ PCIe cards)
DIN-832	DIN35 housing for both OPT-832D and OPT-832W

Analog isolation amplifiers

The daughter boards of the isolation amplifiers are intended for the galvanic isolation of the measured signals with required electric strength. They do not need (unlike the analog multiplexer boards) any auxiliary control ports, every channel has one input of the measuring card assigned. BNC connectors or terminals are alternatively used for input signals.

OPT-1020	single-channel isolation amplifier with a high accuracy (bandwidth 20kHz, isolation voltage 2.5kV_RMS, screw terminals) (with DAQ PCIe cards an external power supply must be used)
OPT-1020B	single-channel isolation amplifier with a high accuracy (bandwidth 20kHz, isolation voltage 2.5kV_RMS, BNC connector) (with DAQ PCIe cards an external power supply must be used)
OPT-1120	single-channel isolation amplifier with a high accuracy (bandwidth 120kHz, isolation voltage 1.5kV_RMS, screw terminals) (with DAQ PCIe cards an external power supply must be used)
OPT-1120B	single-channel isolation amplifier with a high accuracy (bandwidth 120kHz, isolation voltage 1.5kV_RMS, BNC connector) (with DAQ PCIe cards an external power supply must be used)

External boards for conditioning of digital signals

The boards are intended for for TTL/HC signal conditioning of DAQ card digital ports according to the technological requirements, i.e. they provide conversion of signal levels and optical isolation.

Note: Unlike the PCE-16xx series (see below), insulation voltage between technological signals and digital port is not limited by the D-Sub connector features.

OPT-821A	isolated digital input board for 8-bit digital ports (24V_DC signal level)
OPT-851A	isolated digital output board for 8-bit digital ports (24V_DC signal level)
OPT-861	isolated relay output board for 8-bit digital ports
DIN-801	DIN35 housing for all OPT-821A, OPT-851A and OPT-861

Internal boards for conditioning of digital signals,
cables with the card mounting bracket

The boards are intended to be installed into the card slot next to the DAQ card. They serve for TTL/HC signal conditioning of DAQ card digital ports according to the technological requirements, i.e. they provide conversion of signal levels and optical isolation.

Note: Unlike the OPT-8xx series (see above), insulation voltage between technological signals and digital port is limited by the D-Sub connector features.

PCE-1601	8 relay outputs (30V_DC/100V_AC) and 8 inputs (24V_DC signal level)
PCE-1602	8 "PNP" outputs (32V_DC) and 8 inputs (24V_DC signal level)
PCE-1603	two blocks of 8 inputs (24V_DC signal level)
PCE-1604	two blocks of 8 "PNP" outputs (32V_DC)
PCE-1611	8 relay outputs (30V_DC/100V_AC) and 8 non-isolated TTL/HC signals
PCE-1612	8 "PNP" outputs (32V_DC) and 8 non-isolated TTL/HC signals
PCE-1613	8 inputs (24V_DC signal level) and 8 non-isolated TTL/HC signals
PCE-1620	cable with two D-Sub 9 connectors on the mounting bracket two blocks of non-isolated TTL/HC signals (two 8-bit DIO ports)
PCE-8025/LP	cable with one D-Sub 25 connectors on the mounting bracket 24 non-isolated TTL/HC signals (three 8-bit DIO ports) (for low-profile DAQ PCIe cards only)

Terminal boards

A comprehensive terminal board series for peripherals of all DAQ cards is supplied.
Housing for mounting on the DIN35 rail are available as well.

OPT-09	universal terminal board with D-Sub 9
OPT-25A	terminal board with D-Sub 25, designed for analog inputs and outputs
OPT-25D	universal terminal board with D-Sub 25
DIN-09	DIN35 housing for OPT-09
DIN-25	DIN35 housing for both OPT-25A and OPT-25D

DIN35 housing

A comprehensive set of DIN35 housings for external boards and terminal boards is supplied.
After removing rail fastening clips the housings can be also used in the laboratories for free placement of boards on the workbench.

DIN-09	DIN35 housing for OPT-09
DIN-25	DIN35 housing for OPT-25A/25D
DIN-801	DIN35 housing for OPT-821/821A/851/851A/861
DIN-830	DIN35 housing for OPT-830A/830B
DIN-832	DIN35 housing for OPT-832D/832W

Cables etc.

Round shielded cables with D-Sub 9 and D-Sub 25 connectors in lengths 1.8÷10 meters.
Flat unshielded cables with D-Sub 9 and D-Sub 25 connectors in lengths 0.1÷30 meters.
Flat unshielded cables with dual-row connectors for pin-headers in lengths 0.1÷30 meters.

The most frequently used types:

CAB-0911/2	round shielded cable D-Sub 9 (female), D-Sub 9 (male), length 1.8m, 1:1 connectors pin connection
CAB-2511/2	round shielded cable D-Sub 25 (female), D-Sub 25 (male), length 1,8m, 1:1 connectors pin connection
	And variety of other cables ...